Development of a method for the combined control of the hardness of winding textile package

Keywords: winding, winding hardness, layer-by-layer hardness, winding defects, winding density, technological properties, package permeability

Abstract

Analysis of methods for determining the hardness of the winding shows that all existing methods require a lot of labor and time. When measuring the layer-by-layer hardness, the known methods do not allow obtaining continuous values, and in the case of measuring the hardness of packages of complex shape (conical bobbins, cops, spinning cobs, etc.), it requires a calculation using cumbersome formulas. In this case, the main difficulties arise in determining the volume of the layers of the winding, which in the general case have a complex configuration, and due to defects in the winding may have an irregular shape. Obviously, the described technique is rather cumbersome, and a lot of measurements and calculations are required to obtain a graph of the change in the winding hardness along the package radius. The construction of a graph of the change in hardness along the generatrix using a special device is generally problematic, since placement of more than three sources on the device is impossible due to the size of the meters, and the construction of the curve by three points cannot be considered satisfactory. Winding hardness is one of the most important parameters, on which many technological properties of the package depend. Indeed, with an increase in the hardness of the winding, the amount of material in the same volume increases, which makes it possible to replace packages less often, both on the machine that forms them, and at the subsequent transition. As a result, the equipment useful time increases.

It was found that the hardness of the winding is closely related to its rigidity, and hence to the stability during transportation. The hardness of the winding affects the permeability of the package when it is treated with solutions. In this case, a huge role is played not only by the average value of the hardness, but also by its distribution over the layers

Downloads

Download data is not yet available.

Author Biographies

Mahammadali Nuraddin Nuriyev, Azerbaijan State Economic University (UNEC)

Department of Engineering and Applied Sciences

Afet Mastan Jafarova, Azerbaijan State Economic University (UNEC)

Department of Engineering and Applied Sciences

References

Kiselev, А. M., Khilov, P. A., Pryakhin, V. S., Aleinikov, P. A., Kiselev, M. V. (2018). Development of the method of quality control wholly woven 3D preforms with application of computer tomography. Tekhnologiya tekstil'noy promyshlennosti, 4 (376), 110–115. Available at: https://ttp.ivgpu.com/wp-content/uploads/2018/11/376_23.pdf

Yamschikov, A. V. (2003). Razrabotka tekhnologii i ustroystv dlya formirovaniya mokroy nekruchenoy rovnitsy iz l'na. Kostroma, 146.

Rudovskii, P. N. (1996). The relationship between winding structure, sloughing off and breakages during rewinding. Tekhnologiya Tekstil'noi Promyshlennosti, 6, 40–44. Available at: https://www.scopus.com/record/display.uri?eid=2-s2.0-0030389811&origin=inward&txGid=03d67757050609796e965b02abd7cf86

Nekhoroshkina, M. S., Rudovsky, P. N., Bukalov, G. K., Krivosheina, E. V. (2014). Justification of indenter shape during experimental investigation of the protective properties of fabrics. Izvestiya Vysshikh Uchebnykh Zavedenii, Seriya Teknologiya Tekstil'noi Promyshlennosti, 5, 18–22. Available at: https://www.scopus.com/record/display.uri?eid=2-s2.0-84937440922&origin=inward&txGid=28dd4ce72a4d4ddc757f52d4d57f2489

Kolčavová Sirková, B., Vyšanská, M. (2012). Methodology for evaluation of fabric geometry on the basis of the fabric cross-section. Fibres & Textiles in Eastern Europe, 20 (5 (94)), 41–47. Available at: https://dspace.tul.cz/bitstream/handle/15240/16406/2-s2.0-84871246034-o.pdf?sequence=1&isAllowed=y

Nekhoroshkina, M. S., Rudovsky, P. N. (2015). Method of definition for part of collision energy which is absorbed by fabric or fabric-package. Izvestiya Vysshikh Uchebnykh Zavedenii, Seriya Teknologiya Tekstil'noi Promyshlennosti, 355 (1), 53–56. Available at: https://www.scopus.com/record/display.uri?eid=2-s2.0-84938603277&origin=inward&txGid=7e02cac0655e28533120ab161bbe13f2

Tverdomery i tolschinomery. Available at: https://www.metrotex.ru/categories/tverdomery

Tverdomery po Shor i IRHD. Available at: https://www.zwickroell.com/ru/produkcija/mashiny-dlja-opredelenija-tverdosti/tverdomery-po-shor-irhd/

Rudovsky, P. N., Bukalov, G. K. (2012). Calculation of energy loss for modification of a fabric shape under two bodies contact. Izvestiya Vysshikh Uchebnykh Zavedenii, Seriya Teknologiya Tekstil'noi Promyshlennosti, 1, 145–149. Available at: https://www.scopus.com/inward/record.uri?eid=2-s2.0-84868567804&partnerID=40&md5=8290e054a45a083fa3ae62bb8ab3495

Praček, S., Pušnik, N., Simončič, B., Tavčer, F. (2015). Model for Simulating Yarn Unwinding from Packages. FIBRES & TEXTILES in Eastern Europe, 23 (2 (110)), 25–32. Available at: http://www.fibtex.lodz.pl/article1407.html

Trisch, R., Gorbenko, E., Dotsenko, N., Kim, N., Kiporenko, G. (2016). Development of qualimetric approaches to the processes of quality management system at enterprises according to international standards of the ISO 9000 series. Eastern-European Journal of Enterprise Technologies, 4 (3 (82)), 18–24. doi: https://doi.org/10.15587/1729-4061.2016.75503

Grechukhin, A., Rudovskiy, P., Sokova, G., Korabelnikov, A. (2019). Carbon fabric 3D modeling according to nonlinear bending theory. The Journal of The Textile Institute, 111 (10), 1511–1517. doi: https://doi.org/10.1080/00405000.2019.1707935

Nuriyev, M. N., Seydaliyev, I. M., Recebov, I. S., Dadashova, K. S., Musayeva, T. T. (2017). Determining the dependences for calculating a conversion scale of profile height of the controlled packing surface. Eastern-European Journal of Enterprise Technologies, 2 (1 (86)), 58–62. doi: https://doi.org/10.15587/1729-4061.2017.96977

Nuriev, M. N., Rudovskiy, P. N. (2007). Pat. No. 72317 RU. Ustroystvo dlya kompleksnogo kontrolya tekhnologicheskih parametrov pakovok krestovoy namotki. No. 2007142129/22; declareted: 14.11.2007; published: 10.04.2008. Available at: https://i.moscow/patents/RU72317U1_20080410

Dzhabbarova, G. Z., Nuriev, M. N. (2017). Formation packages with а sinusoidal rate of change of the yarn feeder. Tekhnologiya tekstil'noy promyshlennosti, 2, 176–180. Available at: https://ttp.ivgpu.com/wp-content/uploads/2017/07/368_39.pdf

Nuriev, M. N., Rudovskiy, P. N. (2007). Pat. No. 2390017 RU. Sposob nepreryvnogo kontrolya tverdosti namotki i ustroystvo dlya ego osuschestvleniya. No. 2007110127/11; declareted: 19.03.2007; published: 20.05.2010. Available at: https://www.freepatent.ru/patents/2390017

Nuriyev, M., Veliev, F., Seydaliyev, I. M., Dadashova, K., Jabbarova, G. Z., Allahverdiyeva, I. (2017). Analysis of the formation of filament winding in terms of force interactions between threads. Eastern-European Journal of Enterprise Technologies, 6 (1 (90)), 11–18. doi: https://doi.org/10.15587/1729-4061.2017.118961


👁 19
⬇ 18
Published
2022-01-10
How to Cite
Nuriyev, M. N., & Jafarova, A. M. (2022). Development of a method for the combined control of the hardness of winding textile package. EUREKA: Physics and Engineering, (1), 74-84. https://doi.org/10.21303/2461-4262.2022.002237
Section
Engineering

Most read articles by the same author(s)