METHODOLOGY OF EXPERIMENTAL INVESTIGATIONS OF VALVE OPERATION

  • Natig Sabir Seyidahmadov Azerbaijan State Scientific Research Institute of Labor Protection and Technical Safety, Azerbaijan
Keywords: direct-flow valves, purge chamber, valve plates, tightness, oil, gas, gas lift operation, gas-engine piston compressor

Abstract

Tightness, as well as the reliability of the valve plate, is a complex property of the effective operation of compressor cylinders of the first stage and, in general, gas-engine reciprocating compressors. The issue of valve plate tightness is a subject of independent study, since technical and economic efficiency depends on their work. In this connection, only some data obtained under operating conditions are presented in this work.

As a research result, it is found that, taking into account the identified requirements for the gas lift system, in order to effectively increase the operating hours of valves with increased tightness of the plate, it is necessary to check and purge the valves. Therefore, each valve in the gas lift compressor station, without subjecting them to cleaning, is first recommended to check for leaks. To confirm the feasibility of checking valve tightness, special equipment is offered for each gas-lift compressor station, a purge chamber, on which the tightness of valve plates is checked.

The usefulness and importance of the purge chamber is in preparation of the valve at the gas lift compressor station, which contributes to increased efficiency, safe operation, normal tightness and reliability of its operation.

Downloads

Download data is not yet available.

References

Aliev, V. I. (2007). Nauchnye osnovy povysheniya ehffektivnosti raboty gazomotokompressorov v sistemah gazlifta i transporta gaza morskih mestorozhdeniy Azerbaydzhana. Baku, 317.

Lieberman, N. (2019). How Compressors Work. Understanding Process Equipment for Operators and Engineers, 241–250. doi: https://doi.org/10.1016/b978-0-12-816161-6.00031-x

De Coning, P., Swinley, J. (2019). Valves. A Practical Guide to Gas Analysis by Gas Chromatography, 133–163. doi: https://doi.org/10.1016/b978-0-12-818888-0.00005-x

Townsend, J., Badar, M. A., Szekerces, J. (2016). Updating temperature monitoring on reciprocating compressor connecting rods to improve reliability. Engineering Science and Technology, an International Journal, 19 (1), 566–573. doi: https://doi.org/10.1016/j.jestch.2015.09.012

Pont, A., López, J., Rigola, J., Pérez-Segarra, C. D. (2017). Numerical dynamic analysis of reciprocating compressor mechanism. Parametric studies for optimization purposes. Tribology International, 105, 1–14. doi: https://doi.org/10.1016/j.triboint.2016.06.019

Sharma, V., Parey, A. (2019). Performance evaluation of decomposition methods to diagnose leakage in a reciprocating compressor under limited speed variation. Mechanical Systems and Signal Processing, 125, 275–287. doi: https://doi.org/10.1016/j.ymssp.2018.07.029

Loukopoulos, P., Zolkiewski, G., Bennett, I., Sampath, S., Pilidis, P., Duan, F. et. al. (2019). Reciprocating compressor prognostics of an instantaneous failure mode utilising temperature only measurements. Applied Acoustics, 147, 77–86. doi: https://doi.org/10.1016/j.apacoust.2017.12.003

Qi, G., Zhu, Z., Erqinhu, K., Chen, Y., Chai, Y., Sun, J. (2018). Fault-diagnosis for reciprocating compressors using big data and machine learning. Simulation Modelling Practice and Theory, 80, 104–127. doi: https://doi.org/10.1016/j.simpat.2017.10.005

Reis, M. N. E., Hanriot, S. (2017). Incompressible pulsating flow for low Reynolds numbers in orifice plates. Flow Measurement and Instrumentation, 54, 146–157. doi: https://doi.org/10.1016/j.flowmeasinst.2017.01.001

Pravila 28–64 izmereniya rashoda zhidkostey gazov i parov standartnymi diafragmami i soplami (1978). Мoscow, 151.

Plastinin, P. I. (2008). Porshnevye kompressory. Vol. 2. Moscow: Kolos S, 711.

Kudźma, Z., Stosiak, M. (2015). Studies of flow and cavitation in hydraulic lift valve. Archives of Civil and Mechanical Engineering, 15 (4), 951–961. doi: https://doi.org/10.1016/j.acme.2015.05.003

Loukopoulos, P., Zolkiewski, G., Bennett, I., Sampath, S., Pilidis, P., Li, X., Mba, D. (2019). Abrupt fault remaining useful life estimation using measurements from a reciprocating compressor valve failure. Mechanical Systems and Signal Processing, 121, 359–372. doi: https://doi.org/10.1016/j.ymssp.2018.09.033

Mirzadzhanzade, A. H., Stepanova, G. S. (1977). Matematicheskaya teoriya ehksperimenta v dobyche nefti i gaza. Moscow: «Nedra», 228.

Nalimov, V. V., Chernova, N. A. (1965). Statisticheskie metody planirovaniya ehkstremal'nyh ehksperimentov. Moscow: «Nauka», 345.


👁 435
⬇ 258
Published
2019-09-16
How to Cite
Seyidahmadov, N. S. (2019). METHODOLOGY OF EXPERIMENTAL INVESTIGATIONS OF VALVE OPERATION. EUREKA: Physics and Engineering, (5), 56-63. https://doi.org/10.21303/2461-4262.2019.00991
Section
Engineering